STAINLESS STEEL LOW PRESSURE BSP FITTINGS

ANA SAYFA METALLER PASLANMAZ ÇELIK PASLANMAZ ÇELİK BORU ÜRÜNLERİ Archive by category "STAINLESS STEEL LOW PRESSURE BSP FITTINGS"

BSP fittings are a family of fittings used to connect up threaded pipe and equipment. They are manufactured from pipe, bar, hollow bar, castings or forgings.

Stainless Steel BSP Fittings Rangs

İhtiyacınız olan ürünü arayın

Çin'de güçlü işleme tesisleriyle desteklenen geniş bir hizmet merkezi ağı.

Popüler Anahtar Kelimeler

Kategoriler

Kayıt Bulunamadı

Tüm Sonuçları Görüntüle

Menzil

The pipe to be threaded must have a wall thickness of Schedule 40S minimum.
The fittings are used in non-critical, low pressure applications where welding is not possible or required. They therefore provide a relatively low cost method of connection.
BSP fittings are made only in type 316.
BSP fittings are usually fitted with a sealant (paste or tape such as PTFE) and are considered to be permanent pipe-work.
Low Pressure BSP Fittings are rated at 150lb and are made to wrought iron specification BS1740. BSP fittings are made only in type 316.
They are provided with a Certificate of Conformity only, and not a full Test Certificate.
Sizes ½ to 3 inch are the most commonly used and thus the most readily available.
External MALE threads are tapered and Internal FEMALE threads are parallel. The threads are cut to BS21: Part 1: 1985 and are called Whitworth Threads.

low-pressure-cross

low-pressure-hexagon-nut

low-pressure-reducing-bush

low-pressure-square-head-plug

low-pressure-hose-connector

low-pressure-hexagon-head-plug

low-pressure-welding-nipple

low-pressure-barrel-nipple

low-pressure-cap

low-pressure-equal-nipple

low-pressure-reducing-nipple

low-pressure-hexagon-nipple

low-pressure-reducing-socket

low-pressure-round-nut

low-pressure-socket

low-pressure-half-socket

low-pressure-45-elbow

low-pressure-union

low-pressure-equal-tee

low-pressure-90-elbow

90o Elbow: Enables the pipe run to be turned through a right angle. Female thread both ends.
45o Elbow: Enables the pipe run to be turned through 45 degrees. Female thread both ends.
Equal Tee: This allows the connection of a branch at right angles from the main pipe run. Female thread at all three connections.
Socket: Used to connect two pipes or fittings that have male threads. Female thread both ends.
Half Socket: Used to connect two pipes or fittings that have male threads. Used when there is a confined space. Female thread both ends.
Reducing Socket: Used to connect two different sizes of pipe or fittings that have male threads. Female threads both ends.
Cap: Used to terminate a male threaded pipe run. Female threaded.
Union: Connects male threaded pipe or components. Used when easy or regular access is required e.g. for cleaning. Female thread both ends.
Hexagon Nut: Used to fix male threaded fittings. Female threaded.
Reducing Bush: Connects a larger female threaded component to a smaller male threaded component. Male thread at the large end and Female thread at the small end.
Hexagon Nipple: Used to connect two female threaded components. Male thread both ends.
Hexagon Reducing Nipple: Connects two female threaded components of different sizes. Male thread both ends.
Barrel Nipple: Used to connect two female threaded components of the same size. Male (taper) thread both ends.
Parallel or Equal Nipple: The only BSP fitting to have a male parallel thread. Used to connect female threaded components together.
Spigot or Welding Nipple: Weld prepared at one end and a male thread at the other. Used to weld onto equipment that is to be connected to a female threaded component.
Close Taper Nipple: Used to connect two female threaded components. No land between the threads so shorter than a barrel nipple and thus used where space is restricted. Male thread both ends.
Hexagon Head Plug: Used to blank off female threaded outlet. Cannot be used to blank off a pipe directly as pipes only have male threads. Male threaded.
Square Head Plug: Used to blank off female threaded outlet. Cannot be used to blank off a pipe directly as pipes only have male threads. Male threaded.
90o Bend: This has a larger radius than a 90-degree elbow and is again used to turn the pipe run through a right angle. Female thread both ends.
Hose Nipple: Used to connect a hose to the system. Male thread one end and hose serrations at the other.

Whitworth Threads/British Standard Pipe Thread

Nominal Size of Outlet(in)	Nominal Size of Outlet(mm)	Min O/D(mm)	Min O/D of BodyBehind External Thread (mm)	Min I/D of BodyBehind Internal Thread mm	No of Threadsper Inch
1/8	6	15.0	9.8	8.6	28
1/4	8	18.5	13.3	11.4	19
3/8	10	22.0	16.8	15.0	19
1/2	15	27.0	21.1	18.6	14
3/4	20	32.5	26.6	24.1	14
1	25	39.5	33.4	30.3	11
1 1/4	32	49.0	42.1	39.0	11
1 1/2	40	56.0	48.0	44.8	11
2	50	68.0	59.8	56.7	11
2 1/2	65	84.0	75.4	72.2	11
3	80	98.0	88.1	84.9	11
4	100	124.0	113.3	110.1	11
5	125	151.0	138.7	135.5	11
6	150	178.0	164.1	160.9	11